DEVELOPMENT OF AN OPTIMIZED PERFORMANCE-GRADED (PG) ASPHALT BINDER FOR UZBEKISTAN'S ROAD-CLIMATIC CONDITIONS AND TRAFFIC LOADS: RHEOLOGICAL CHARACTERIZATION AND HYBRID POLYMER MODIFICATION

DIGITAL OBJECT IDENTIFIER (DOI): https://doi.org/10.67620/sai.58a0001
Kurbonov Salohiddin1
1 Tashkent State Transport University, Tashkent, Uzbekistan
ReceivedAug 06, 2026
RevisedAug 21, 2026
PublishedAug 26, 2026

Annotatsiya

This study characterized a BND 50/70 paving-grade asphalt binder used in Uzbekistan and evaluated four polymer-modification strategies designed to achieve a PG 76-28 performance grade. The testing program included rotational viscosity, flash point, dynamic shear rheometer testing of unaged and rolling thin-film oven-aged binders, multiple stress creep recovery (MSCR), pressure aging vessel aging, and bending beam rheometer (BBR) testing. The modifiers were TITAN 7686 plastomer, LG501S styrene-butadiene-styrene elastomer, their hybrid combination, and a hybrid formulation containing 1.0% Reclamite® plasticizer. For base-binder measurements with available duplicates, means, sample standard deviations, and coefficients of variation were calculated. The base binder had a mean viscosity of 0.625 ± 0.038 Pa·s at 135 °C and a mean flash point of 270.0 ± 8.49 °C. Polymer modification increased the reported critical high temperature to 77.62 °C with TITAN 7686, 83.30 °C with 3.0% LG501S, 83.10 °C with the LG501S/TITAN hybrid, and 79.30 °C with the LG501S/TITAN/Reclamite® hybrid. The optimized formulation had an S(60) value of 170 MPa and an m-value of 0.305 at −18 °C, with a reported critical low temperature of approximately −29.1 °C. It was therefore classified as PG 76-28. Because replicate-level observations were unavailable for every modified formulation, inferential statistics were not applied. The results support hybrid elastomeric-plastomeric modification with controlled plasticization, while additional replicate MSCR and mixture-level validation remain necessary before field implementation.

Kalit so'zlar

asphalt binder, performance grade, polymer modification, MSCR, BBR, Uzbekistan.

Foydalanilgan adabiyotlar

1. American Association of State Highway and Transportation Officials. (2023). Standard specification for performance-graded asphalt binder (AASHTO M 320-23). 2. ASTM International. (2022). Standard test method for effect of heat and air on a moving film of asphalt binder (rolling thin-film oven test) (ASTM D2872-22). https://doi.org/10.1520/D2872-22 3. ASTM International. (2023a). Standard specification for performance-graded asphalt binder (ASTM D6373-23). https://doi.org/10.1520/D6373-23 4. ASTM International. (2023b). Standard test method for viscosity determination of asphalt at elevated temperatures using a rotational viscometer (ASTM D4402/D4402M-23). https://doi.org/10.1520/D4402_D4402M-23 5. ASTM International. (2024). Standard test method for multiple stress creep recovery (MSCR) of asphalt binder using a dynamic shear rheometer (ASTM D7405-24). 6. ASTM International. (2025a). Standard test method for determining the flexural creep stiffness of asphalt binder using the bending beam rheometer (BBR) (ASTM D6648-25a). https://doi.org/10.1520/D6648-25A 7. ASTM International. (2025b). Standard test method for determining the rheological properties of asphalt binder using a dynamic shear rheometer (ASTM D7175-25). https://doi.org/10.1520/D7175-25 8. Bahia, H. U., Hanson, D. I., Zeng, M., Zhai, H., Khatri, M. A., & Anderson, R. M. (2001). Characterization of modified asphalt binders in Superpave mix design (NCHRP Report 459). Transportation Research Board. 9. Behnood, A., & Gharehveran, M. M. (2019). Morphology, rheology, and physical properties of polymer-modified asphalt binders. European Polymer Journal, 112, 766–791. https://doi.org/10.1016/j.eurpolymj.2018.10.049 10. GOST 33137-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determination of dynamic viscosity using a rotational viscometer. (2014). 11. GOST 33140-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determining aging under the influence of high temperature and air (RTFOT method). (2014). 12. GOST 33141-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determination of flash point using the Cleveland open cup method. (2014). 13. GOST R 58400.1-2019. General automobile roads. Petroleum-based bitumen binders. Specifications taking into account the temperature range of operation. (2019). 14. GOST R 58400.10-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method for determination of properties using a dynamic shear rheometer (DSR). (2019). 15. GOST R 58400.5-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of aging under the action of pressure and temperature (PAV). (2019). 16. GOST R 58400.6-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of determining elastic properties at multiple shear loads (MSCR) using a dynamic shear rheometer (DSR). (2019). 17. GOST R 58400.8-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of determining flexural creep stiffness at subzero temperatures using the bending beam rheometer (BBR). (2019). 18. Liu, H., Zeiada, W., Al-Khateeb, G. G., Shanableh, A., & Samarai, M. (2021). Use of the multiple stress creep recovery (MSCR) test to characterize the rutting potential of asphalt binders: A literature review. Construction and Building Materials, 269, 121320. https://doi.org/10.1016/j.conbuildmat.2020.121320 19. Sadikov, I. S., Karabaev, A. M., & Ashurov, F. B. (2021). Results of evaluation of extreme temperatures in different territories of the Republic of Uzbekistan with the “Superpave” method. Journal of Academic Research and Trends in Educational Sciences, 1(1), 56–64. https://doi.org/10.5281/zenodo.5753294 20. Urakov, A., Tashev, D., Xametov, Z., & Soataliev, R. (2022). Road maintenance and climate zoning of the territory of the Republic of Uzbekistan. In A. Manakov & A. Edigarian (Eds.), International Scientific Siberian Transport Forum TransSiberia 2021 (Lecture Notes in Networks and Systems, Vol. 402, pp. 1213–1224). Springer. https://doi.org/10.1007/978-3-030-96380-4_133 21. West, R., Rodezno, C., Leiva, F., & Yin, F. (2018). Development of a framework for balanced mix design (NCHRP Project 20-07/Task 406 Final Report). Transportation Research Board. 22. Yang, Q., Lin, J., Wang, X., Wang, D., Xie, N., & Shi, X. (2024). A review of polymer-modified asphalt binder: Modification mechanisms and mechanical properties. Cleaner Materials, 12, 100255. https://doi.org/10.1016/j.clema.2024.100255

Maqolaga iqtibos keltirish andozasi

Kurbonov Salohiddin (2026). DEVELOPMENT OF AN OPTIMIZED PERFORMANCE-GRADED (PG) ASPHALT BINDER FOR UZBEKISTAN'S ROAD-CLIMATIC CONDITIONS AND TRAFFIC LOADS: RHEOLOGICAL CHARACTERIZATION AND HYBRID POLYMER MODIFICATION. Science and Innovation, 5(8), 4-13. https://doi.org/10.67620/sai.58a0001