DEVELOPMENT OF AN OPTIMIZED PERFORMANCE-GRADED (PG) ASPHALT BINDER FOR UZBEKISTAN'S ROAD-CLIMATIC CONDITIONS AND TRAFFIC LOADS: RHEOLOGICAL CHARACTERIZATION AND HYBRID POLYMER MODIFICATION
1 Tashkent State Transport University, Tashkent, Uzbekistan
ReceivedAug 06, 2026
RevisedAug 21, 2026
PublishedAug 26, 2026
Abstract
This study characterized a BND 50/70 paving-grade asphalt binder used in Uzbekistan and evaluated four polymer-modification strategies designed to achieve a PG 76-28 performance grade. The testing program included rotational viscosity, flash point, dynamic shear rheometer testing of unaged and rolling thin-film oven-aged binders, multiple stress creep recovery (MSCR), pressure aging vessel aging, and bending beam rheometer (BBR) testing. The modifiers were TITAN 7686 plastomer, LG501S styrene-butadiene-styrene elastomer, their hybrid combination, and a hybrid formulation containing 1.0% Reclamite® plasticizer. For base-binder measurements with available duplicates, means, sample standard deviations, and coefficients of variation were calculated. The base binder had a mean viscosity of 0.625 ± 0.038 Pa·s at 135 °C and a mean flash point of 270.0 ± 8.49 °C. Polymer modification increased the reported critical high temperature to 77.62 °C with TITAN 7686, 83.30 °C with 3.0% LG501S, 83.10 °C with the LG501S/TITAN hybrid, and 79.30 °C with the LG501S/TITAN/Reclamite® hybrid. The optimized formulation had an S(60) value of 170 MPa and an m-value of 0.305 at −18 °C, with a reported critical low temperature of approximately −29.1 °C. It was therefore classified as PG 76-28. Because replicate-level observations were unavailable for every modified formulation, inferential statistics were not applied. The results support hybrid elastomeric-plastomeric modification with controlled plasticization, while additional replicate MSCR and mixture-level validation remain necessary before field implementation.
1. American Association of State Highway and Transportation Officials. (2023). Standard specification for performance-graded asphalt binder (AASHTO M 320-23).
2. ASTM International. (2022). Standard test method for effect of heat and air on a moving film of asphalt binder (rolling thin-film oven test) (ASTM D2872-22). https://doi.org/10.1520/D2872-22
3. ASTM International. (2023a). Standard specification for performance-graded asphalt binder (ASTM D6373-23). https://doi.org/10.1520/D6373-23
4. ASTM International. (2023b). Standard test method for viscosity determination of asphalt at elevated temperatures using a rotational viscometer (ASTM D4402/D4402M-23). https://doi.org/10.1520/D4402_D4402M-23
5. ASTM International. (2024). Standard test method for multiple stress creep recovery (MSCR) of asphalt binder using a dynamic shear rheometer (ASTM D7405-24).
6. ASTM International. (2025a). Standard test method for determining the flexural creep stiffness of asphalt binder using the bending beam rheometer (BBR) (ASTM D6648-25a). https://doi.org/10.1520/D6648-25A
7. ASTM International. (2025b). Standard test method for determining the rheological properties of asphalt binder using a dynamic shear rheometer (ASTM D7175-25). https://doi.org/10.1520/D7175-25
8. Bahia, H. U., Hanson, D. I., Zeng, M., Zhai, H., Khatri, M. A., & Anderson, R. M. (2001). Characterization of modified asphalt binders in Superpave mix design (NCHRP Report 459). Transportation Research Board.
9. Behnood, A., & Gharehveran, M. M. (2019). Morphology, rheology, and physical properties of polymer-modified asphalt binders. European Polymer Journal, 112, 766–791. https://doi.org/10.1016/j.eurpolymj.2018.10.049
10. GOST 33137-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determination of dynamic viscosity using a rotational viscometer. (2014).
11. GOST 33140-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determining aging under the influence of high temperature and air (RTFOT method). (2014).
12. GOST 33141-2014. Motor roads of general use. Viscous petroleum road bitumens. Method for determination of flash point using the Cleveland open cup method. (2014).
13. GOST R 58400.1-2019. General automobile roads. Petroleum-based bitumen binders. Specifications taking into account the temperature range of operation. (2019).
14. GOST R 58400.10-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method for determination of properties using a dynamic shear rheometer (DSR). (2019).
15. GOST R 58400.5-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of aging under the action of pressure and temperature (PAV). (2019).
16. GOST R 58400.6-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of determining elastic properties at multiple shear loads (MSCR) using a dynamic shear rheometer (DSR). (2019).
17. GOST R 58400.8-2019. Automobile roads of general use. Petroleum-based bitumen binders. Method of determining flexural creep stiffness at subzero temperatures using the bending beam rheometer (BBR). (2019).
18. Liu, H., Zeiada, W., Al-Khateeb, G. G., Shanableh, A., & Samarai, M. (2021). Use of the multiple stress creep recovery (MSCR) test to characterize the rutting potential of asphalt binders: A literature review. Construction and Building Materials, 269, 121320. https://doi.org/10.1016/j.conbuildmat.2020.121320
19. Sadikov, I. S., Karabaev, A. M., & Ashurov, F. B. (2021). Results of evaluation of extreme temperatures in different territories of the Republic of Uzbekistan with the “Superpave” method. Journal of Academic Research and Trends in Educational Sciences, 1(1), 56–64. https://doi.org/10.5281/zenodo.5753294
20. Urakov, A., Tashev, D., Xametov, Z., & Soataliev, R. (2022). Road maintenance and climate zoning of the territory of the Republic of Uzbekistan. In A. Manakov & A. Edigarian (Eds.), International Scientific Siberian Transport Forum TransSiberia 2021 (Lecture Notes in Networks and Systems, Vol. 402, pp. 1213–1224). Springer. https://doi.org/10.1007/978-3-030-96380-4_133
21. West, R., Rodezno, C., Leiva, F., & Yin, F. (2018). Development of a framework for balanced mix design (NCHRP Project 20-07/Task 406 Final Report). Transportation Research Board.
22. Yang, Q., Lin, J., Wang, X., Wang, D., Xie, N., & Shi, X. (2024). A review of polymer-modified asphalt binder: Modification mechanisms and mechanical properties. Cleaner Materials, 12, 100255. https://doi.org/10.1016/j.clema.2024.100255
How to Cite
Kurbonov Salohiddin (2026). DEVELOPMENT OF AN OPTIMIZED PERFORMANCE-GRADED (PG) ASPHALT BINDER FOR UZBEKISTAN'S ROAD-CLIMATIC CONDITIONS AND TRAFFIC LOADS: RHEOLOGICAL CHARACTERIZATION AND HYBRID POLYMER MODIFICATION. Science and Innovation, 5(8), 4-13. https://doi.org/10.67620/sai.58a0001