1 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
2 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
3 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
4 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
5 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
6 S.A. Azimov Physics-Technical Institute, Academy of Sciences of the Republic of Uzbekistan, 2B Chingz Aitmatov Street, Tashkent 100084, Uzbekistan
ReceivedJul 18, 2026
RevisedAug 02, 2026
PublishedAug 07, 2026
Abstract
In this study, the structural and electrophysical properties of SbxSey thin films grown at different source temperatures using the independent-source vapor transport method were investigated. The composition of the thin films was determined by energy-dispersive X-ray spectroscopy (EDS), revealing that as the source temperature increases, the Sb/Se atomic ratio shifts from Se-rich to Sb-rich. Specifically, a Se-rich composition (Sb/Se ≈ 0.51) was observed in films obtained at 500 °C, a stoichiometric composition (Sb/Se ≈ 0.67) at 525 °C, and an Sb-rich composition (Sb/Se ≈ 0.82) at 550 °C. The temperature dependence of electrical conductivity was measured using a cryostat, and activation energies were calculated from Arrhenius analysis. According to the results, the following activation energies were identified for the corresponding samples: Eᵥ + 0.578 eV for the 500 °C film, Eᵥ + 0.111 eV for the 525 °C film, and E꜀ − 0.518 eV for the 550 °C film.
Keywords
independent-source vapor transport deposition, Sb₂Se₃ thin-film solar cells, substrate preparation, source temperature effect, point defects, electrical conductivity, activation energy, photovoltaic absorber materials.
References
1. Chen, C., Bobela, D. C., Yang, Y., Lu, S., Zeng, K., Ge, C., Yang, B., Gao, L., Zhao, Y., Beard, M. C., & Tang, J. (2017). Characterization of basic physical properties of Sb2Se3 and its relevance for photovoltaics. Frontiers of Optoelectronics, 10(1), 18–30. https://doi.org/10.1007/s12200-017-0702-z
2. Chen, C., Wang, L., Gao, L., Nam, D., Li, D., Li, K., Zhao, Y., Ge, C., Cheong, H., Liu, H., Song, H., & Tang, J. (2017). 6.5% Certified Efficiency Sb 2 Se 3 Solar Cells Using PbS Colloidal Quantum Dot Film as Hole-Transporting Layer. ACS Energy Letters, 2(9), 2125–2132. https://doi.org/10.1021/acsenergylett.7b00648
3. Dong, J., Liu, Y., Wang, Z., & Zhang, Y. (2021). Boosting V OC of antimony chalcogenide solar cells: A review on interfaces and defects. Nano Select, 2(10), 1818–1848. https://doi.org/10.1002/nano.202000288
4. Gharibshahian, I., Orouji, A. A., & Sharbati, S. (2020). Towards high efficiency Cd-Free Sb2Se3 solar cells by the band alignment optimization. Solar Energy Materials and Solar Cells, 212, 110581. https://doi.org/10.1016/j.solmat.2020.110581
5. Ghosh, S., Moreira, M. V. B., Fantini, C., & González, J. C. (2020). Growth and optical properties of nanocrystalline Sb2Se3 thin-films for the application in solar-cells. Solar Energy, 211, 613–621. https://doi.org/10.1016/j.solener.2020.10.001
6. Green, M., Dunlop, E., Hohl‐Ebinger, J., Yoshita, M., Kopidakis, N., & Hao, X. (2021). Solar cell efficiency tables (version 57). Progress in Photovoltaics: Research and Applications, 29(1), 3–15. https://doi.org/10.1002/pip.3371
7. Hobson, T. D. C., Hutter, O. S., Fleck, N., Daniels, L. M., Major, J. D., Ng, T. M., & Durose, K. (2020). Vegard Relation and Raman Band Reference Data Generated from Bulk Crystals of Kesterite-Phase Composition Series Cu 2 ZnSnS 4 x Se 4–4 x (CZTSSe, 0 ≤ x ≤ 1). Crystal Growth & Design, 20(4), 2164–2173. https://doi.org/10.1021/acs.cgd.9b00911
8. Hobson, T. D. C., Phillips, L. J., Hutter, O. S., Durose, K., & Major, J. D. (2020). Defect properties of Sb2Se3 thin film solar cells and bulk crystals. Applied Physics Letters, 116(26). https://doi.org/10.1063/5.0012697
9. Huang, M., Cai, Z., Wang, S., Gong, X., Wei, S., & Chen, S. (2021). More Se Vacancies in Sb 2 Se 3 under Se‐Rich Conditions: An Abnormal Behavior Induced by Defect‐Correlation in Compensated Compound Semiconductors. Small, 17(36), 2102429. https://doi.org/10.1002/smll.202102429
10. Huang, M., Xu, P., Han, D., Tang, J., & Chen, S. (2019). Complicated and Unconventional Defect Properties of the Quasi-One-Dimensional Photovoltaic Semiconductor Sb 2 Se 3. ACS Applied Materials & Interfaces, 11(17), 15564–15572. https://doi.org/10.1021/acsami.9b01220
11. Hutter, O. S., Phillips, L. J., Durose, K., & Major, J. D. (2018). 6.6% efficient antimony selenide solar cells using grain structure control and an organic contact layer. Solar Energy Materials and Solar Cells, 188, 177–181. https://doi.org/10.1016/j.solmat.2018.09.004
12. Kondrotas, R., Zhang, J., Wang, C., & Tang, J. (2019). Growth mechanism of Sb2Se3 thin films for photovoltaic application by vapor transport deposition. Solar Energy Materials and Solar Cells, 199, 16–23. https://doi.org/10.1016/j.solmat.2019.04.024
13. Lei, H., Chen, J., Tan, Z., & Fang, G. (2019). Review of Recent Progress in Antimony Chalcogenide‐Based Solar Cells: Materials and Devices. Solar RRL, 3(6). https://doi.org/10.1002/solr.201900026
14. Li, G., Li, Z., Liang, X., Guo, C., Shen, K., & Mai, Y. (2019). Improvement in Sb 2 Se 3 Solar Cell Efficiency through Band Alignment Engineering at the Buffer/Absorber Interface. ACS Applied Materials & Interfaces, 11(1), 828–834. https://doi.org/10.1021/acsami.8b17611
15. Li, Z., Liang, X., Li, G., Liu, H., Zhang, H., Guo, J., Chen, J., Shen, K., San, X., Yu, W., Schropp, R. E. I., & Mai, Y. (2019). 9.2%-efficient core-shell structured antimony selenide nanorod array solar cells. Nature Communications, 10(1), 125. https://doi.org/10.1038/s41467-018-07903-6
16. Liang, G.-X., Luo, Y.-D., Chen, S., Tang, R., Zheng, Z.-H., Li, X.-J., Liu, X.-S., Liu, Y.-K., Li, Y.-F., Chen, X.-Y., Su, Z.-H., Zhang, X.-H., Ma, H.-L., & Fan, P. (2020). Sputtered and selenized Sb2Se3 thin-film solar cells with open-circuit voltage exceeding 500 mV. Nano Energy, 73, 104806. https://doi.org/10.1016/j.nanoen.2020.104806
17. Liu, X., Xiao, X., Yang, Y., Xue, D.-J., Li, D.-B., Chen, C., Lu, S., Gao, L., He, Y., Beard, M. C., Wang, G., Chen, S., & Tang, J. (2017). Enhanced Sb 2 Se 3 solar cell performance through theory-guided defect control. Progress in Photovoltaics: Research and Applications, 25(10), 861–870. https://doi.org/10.1002/pip.2900
18. Ma, Y., Tang, B., Lian, W., Wu, C., Wang, X., Ju, H., Zhu, C., Fan, F., & Chen, T. (2020). Efficient defect passivation of Sb 2 Se 3 film by tellurium doping for high performance solar cells. Journal of Materials Chemistry A, 8(14), 6510–6516. https://doi.org/10.1039/D0TA00443J
19. Mavlonov, A., Razykov, T., Raziq, F., Gan, J., Chantana, J., Kawano, Y., Nishimura, T., Wei, H., Zakutayev, A., & Minemoto, T. (2020). A review of Sb2Se3 photovoltaic absorber materials and thin-film solar cells. Solar Energy, 201, 227–246.
20. Moynihan, C. T., Gavin, D. L., & Syed, R. (1982). PRE-EXPONENTIAL TERM IN THE ARRHENIUS EQUATION FOR ELECTRICAL CONDUCTIVITY OF GLASS. Le Journal de Physique Colloques, 43(C9), C9-395-C9-398. https://doi.org/10.1051/jphyscol:1982975
21. Phillips, L. J., Savory, C. N., Hutter, O. S., Yates, P. J., Shiel, H., Mariotti, S., Bowen, L., Birkett, M., Durose, K., Scanlon, D. O., & Major, J. D. (2019). Current Enhancement via a TiO2 Window Layer for CSS Sb2Se3 Solar Cells: Performance Limits and High V oc. IEEE Journal of Photovoltaics, 9(2), 544–551. https://doi.org/10.1109/JPHOTOV.2018.2885836
22. Savory, C. N., & Scanlon, D. O. (2019). The complex defect chemistry of antimony selenide. Journal of Materials Chemistry A, 7(17), 10739–10744. https://doi.org/10.1039/C9TA02022E
23. Scheer, R., & Schock, H. (2011). Chalcogenide Photovoltaics. Wiley. https://doi.org/10.1002/9783527633708
24. Shiel, H., Hutter, O. S., Phillips, L. J., Swallow, J. E. N., Jones, L. A. H., Featherstone, T. J., Smiles, M. J., Thakur, P. K., Lee, T.-L., Dhanak, V. R., Major, J. D., & Veal, T. D. (2020). Natural Band Alignments and Band Offsets of Sb 2 Se 3 Solar Cells. ACS Applied Energy Materials, 3(12), 11617–11626. https://doi.org/10.1021/acsaem.0c01477
25. Shockley, W., & Queisser, H. J. (1961). Detailed Balance Limit of Efficiency of p-n Junction Solar Cells. Journal of Applied Physics, 32(3), 510–519. https://doi.org/10.1063/1.1736034
26. Streetman, B. G., & Banerjee, S. K. (2015). Solid State Electronic Devices. Pearson, 10(Pearson),596. https://books.google.co.uz/books/about/Solid_State_Electronic_Devices.html?id=-nnznQEACAAJ&redir_esc=y
27. Sze, S. M., & Ng, K. K. (2006). Physics of Semiconductor Devices (3rd ed.). Wiley. https://doi.org/10.1002/0470068329
28. Wang, L., Li, D.-B., Li, K., Chen, C., Deng, H.-X., Gao, L., Zhao, Y., Jiang, F., Li, L., Huang, F., He, Y., Song, H., Niu, G., & Tang, J. (2017). Stable 6%-efficient Sb2Se3 solar cells with a ZnO buffer layer. Nature Energy, 2(4), 17046. https://doi.org/10.1038/nenergy.2017.46
29. Wang, X., Li, Z., Kavanagh, S. R., Ganose, A. M., & Walsh, A. (2022). Lone pair driven anisotropy in antimony chalcogenide semiconductors. Physical Chemistry Chemical Physics, 24(12), 7195–7202. https://doi.org/10.1039/D1CP05373F
30. Wang, X., Tang, R., Wu, C., Zhu, C., & Chen, T. (2018). Development of antimony sulfide–selenide Sb2(S, Se)3-based solar cells. Journal of Energy Chemistry, 27(3), 713–721. https://doi.org/10.1016/j.jechem.2017.09.031
31. Wen, X., He, Y., Chen, C., Liu, X., wang, L., Yang, B., Leng, M., Song, H., Zeng, K., Li, D., Li, K., Gao, L., & Tang, J. (2017). Magnetron sputtered ZnO buffer layer for Sb2Se3 thin film solar cells. Solar Energy Materials and Solar Cells, 172, 74–81. https://doi.org/10.1016/j.solmat.2017.07.014
32. Wijesinghe, U., Longo, G., & Hutter, O. S. (2023). Defect engineering in antimony selenide thin film solar cells. Energy Advances, 2(1), 12–33. https://doi.org/10.1039/D2YA00232A
33. Williams, R. E., Ramasse, Q. M., McKenna, K. P., Phillips, L. J., Yates, P. J., Hutter, O. S., Durose, K., Major, J. D., & Mendis, B. G. (2020). Evidence for Self-healing Benign Grain Boundaries and a Highly Defective Sb 2 Se 3 –CdS Interfacial Layer in Sb 2 Se 3 Thin-Film Photovoltaics. ACS Applied Materials & Interfaces, 12(19), 21730–21738. https://doi.org/10.1021/acsami.0c03690
34. Zakutayev, A. (2017). Brief review of emerging photovoltaic absorbers. Current Opinion in Green and Sustainable Chemistry, 4, 8–15. https://doi.org/10.1016/j.cogsc.2017.01.002
35. Zhou, J., Xu, X., Duan, B., Wu, H., Shi, J., Luo, Y., Li, D., & Meng, Q. (2021). Regulating crystal growth via organic lithium salt additive for efficient Kesterite solar cells. Nano Energy, 89, 106405. https://doi.org/10.1016/j.nanoen.2021.106405
36. Zhou, Y., Leng, M., Xia, Z., Zhong, J., Song, H., Liu, X., Yang, B., Zhang, J., Chen, J., Zhou, K., Han, J., Cheng, Y., & Tang, J. (2014). Solution‐Processed Antimony Selenide Heterojunction Solar Cells. Advanced Energy Materials, 4(8), 1301846. https://doi.org/10.1002/aenm.201301846
37. Zhou, Y., Wang, L., Chen, S., Qin, S., Liu, X., Chen, J., Xue, D.-J., Luo, M., Cao, Y., Cheng, Y., Sargent, E. H., & Tang, J. (2015). Thin-film Sb2Se3 photovoltaics with oriented one-dimensional ribbons and benign grain boundaries. Nature Photonics, 9(6), 409–415. https://doi.org/10.1038/nphoton.2015.78
How to Cite
K.M. Quchqarov, B.A. Ergashev, M.P. Pirimmatov, A.S. Matmuratov, B.A. Gulumbaev, X.Z.To‘liboyeva (2026). INFLUENCE OF DEFECTS ON THE ELECTRICAL CONDUCTIVITY OF SBₓSEᵧ THIN FILMS PREPARED BY THE INDEPENDENT SOURCE VAPOR TRANSPORT TECHNIQUE. Science and Innovation, 5(7), 37-47. https://doi.org/10.67620/sai.57a0004